The interior door is a building material product for each of us. It protects our privacy and is also a security guard at home. What is the installation process of the interior door covers ? Today we will come together to understand the installation process of the interior door insert . Waterproof method for indoor door cover installation process 1. Seal the surface of the parts after sawing with sealing glue or moisture-proof paint, and then use polyurethane foam to fill the gap between the door sleeve and the wall hole after adjusting and fixing the main frame of the door cover (side and front end). The gap was finally sealed with a glass seal to the ground gap. 2. In the same way as the above operation method and flow, the method of spraying or brushing the moisture-proof paint is used instead of the sealing glue, and the grounding gap between the door sleeve and the ground is finally sealed with the glass glue. 3ã€Before installation, use the sealing tape to seal the back of each part of the door pocket, and the grounding surface of the part after the saw is installed. After installation, use a glass glue to seal the grounding gap between the door pocket and the ground. Interior door cover installation process 1, according to the design drawings to check the specifications of the door, open the direction, and related Accessories. 2. The height and width of the door opening are measured by a tape measure. The standard height and width of the door is 200cm×80cm; the height of the bathroom door is 200cm×70cm. Size should be promptly corrected if there is an inconvenience. 3. Measure the position line, determine the position of the door frame, and use the ink fountain to pull out the vertical line. There are two vertical lines on the side of the door. 4. Drill the eye with a percussion drill in the vertical line. The distance between the hole and the hole is about 30cm. There is a total of 10 holes in the two rows of the side door. The impact drill bit should be 12mm, and the depth of the drilled hole is about 6cm. 5. Small wooden wedges are nailed into the holes one by one with a hammer in order to fix the door jamb. The size of the small wooden wedge is 5cm × 1.5cm × 1.5cm. It is better to use larch, because the wooden structure of larch is tight and it is not easy. Loosening. 6, open the production of door frames, left and right sides to do the door frame keel wood board size is 200cm × 3cm × 8cm, door frame top keel wood board size is 80cm × 3cm × 8cm, the high density of nine PCT board glued to the keel , and then fixed with steam gun nails. 7. The prepared three door frames are connected according to the shape of the door, and are fixed at the joint with large nails. 8, with a plane to connect the surface of the door frame trim, trim corners, angular. 9, put the door frame on the door hole, according to the horizontal line of the wall shall prevail, take the wood or brick under the door frame to adjust, adjust the height of the door frame, set aside 5cm buried in the floor of the keel. 10. Nail a nail on the top of the door frame and hang the line upright. Adjust the vertical of the door frame by hanging the line. Measure one side with a twisted nail to fix the door frame on the door hole. 11, the production of the door face of the line, the door face can be purchased off-the-shelf, it can be done by the construction staff in accordance with the drawings. After the production is completed, fix the door face to the door frame six so that the door cover is basically completed. 12. Put the door on the door cover and make a good gesture. Determine the specific position of the hinge on the door cover. Then press the thickness of the hinge to cut the exit path. Also cut out the diameter of the lock sleeve. Install the door on the door cover and tighten the screw with a thread cutter. Note that the gap between the door and the door pocket must not exceed 1.5 mm, whichever is the case. 13. Remove the attachments and dirt on the surface of the door cover, then apply putty. Put a memento paper between the door and the wall before applying the putty to prevent the paint from sticking to the wall. Make sure that it is uniform when applying putty. , fix the door to nail holes. 14, spray paint, paint spray effect will be more delicate, and the details can be brushed. 15. Install the lock on the lock hole, being careful not to damage the paint. Regarding the installation process of the interior door pocket , I will introduce it to you. I hope to help you, and more information on the decoration is on this site. Please stay tuned. Installation Interior Door Interior Steel Door Price Interior Door Line Interior Door White Interior Door Price Solar Mounting Brackets are made of hot galvanized steel Q235 and used for solar pannel in concrete base,roof,ramming pole,carport,green house and etc.They have the advantages of easy instalation, steady and safety,excellent duration and great flexibility. High pre-assembly parts and customized solution to save your install time and money. Solar Mounting System,Advanced Solar Mounting System,Ground Screws for Solar Mounting,Solar Mounting Structure Hebei Honde Plastic & Metal Co., Ltd. , https://www.foundation-system.com
Installation:
1.Ships in a few small boxes reducing material costs and simplifying shipping and handling.
2.No rails means mounts-to-modules instead of mounts-to-rails-to-modules, making installation fast and simple.
3.Works with standard modules. Simply drop in the modules, tighten down the clamps, and you're done.
Features & Benefits:
1.Works with standard module frames - providing greater flexibility
2.Engineered to be structurally robust & simple, with minimal leveling
3.Easy to handle and transport - ships in small boxes
4.Cost savings with integrated grounding, requiring less copper and grounding hardware
5.Elegant, sleek design means more referrals from
happy homeowners
6.Quick Rack comes with easy-to-use design software