Wall cracking can be said to be a very common home living problem. According to incomplete statistics, 90% of owners have encountered the problem of wall cracking. The cracking of the wall may seem like a minor problem, but once it appears, it is extremely annoying. If you leave it alone, it will become a big problem over time. Then, how to deal with the cracking of the wall ? Looking for the right reasons to remedy the disease, the following small series will cause the cracking of the wall to one by one for everyone to answer " how to deal with the cracking of the wall, " this problem. How to deal with cracking walls 1, putty layer cracking The wall scraping putty can make the wall surface smoother and smoother, flatness is much higher than the cement wall surface, so that the paint effect on the wall surface is better and the paint can be saved. However, cracks in the putty layer can easily lead to cracks in the wall surface. Putty layer wall cracking treatment method: If the crack has been putty layer, you can first use a sharp tool to expand the crack to a screwdriver-size look, then fill in the caulking plaster and polish and level, paste the grid cloth or kraft paper with putty Leveling, and finally brushing or wallpapering in accordance with the normal procedure. How to deal with the cracking of the wall 2. Cracking of the wall structure Cracks in the structural layers of the wall itself can also lead to surface cracks. There are two main causes of wall cracking here. First, the original wall itself has cracks, and no appropriate treatment measures have been taken during the subsequent renovation. Second, the original wall surface has no cracks in the fashion of decoration, and cracks occur at later stages due to uneven foundation settlement and large temperature changes. Wall structure cracking treatment method: This cracking ordinary decoration method can not be repaired, must find a professional building structure personnel according to the actual situation, take appropriate measures. How to deal with cracking the wall 3, plaster cracking The plastering layer of the wall is divided into normal cracking and abnormal cracking. Normal cracking mainly refers to cracks in the plaster layer caused by the shrinkage of cement mortar; abnormal cracking is mainly due to cracks caused by improper materials or construction processes. Normal cracking is difficult to avoid, but abnormal cracking can be avoided. Plastering layer cracking treatment method: If there is a large area emptying plaster layer, you should knock out the original plaster layer, do a new mortar layer of cement mortar, leveling and then paint the normal process. However, after such treatment, the cost will increase relatively. If there is only a small area of ​​cracking, there is no turning, emptying, falling off, you can fill the wall really good cloth, and then brush the paint according to the normal process. How to deal with the cracking of the wall 4, cracking of the paint layer The cracking of the paint layer is mainly caused by cracks on the surface of the wall surface caused by the cracking of the wall paint layer. The reason is mainly due to the improper quality of the paint product of the wall paint or improper operation during the construction of the wall paint. Paint cracking treatment method: If it is only the crack of the surface paint film, use a fine sandpaper to grind the cracks, select the same color of the wall paint, re-brushing can be. How to deal with cracking the wall 5, seam cracking Wall cracking at the base can cause cracks in the surface of the wall. Cracks in joints mainly occur at the joints of reinforced concrete shear walls and ceramic bricks, at the joints of reinforced concrete beams and ceramic grain bricks, at the entrances of rear blockages, and between gypsum board partition walls and original wall joints. Department. The cracking of joints is mainly due to the influence of the surrounding environment or external forces. Gypsum board, prefabricated partition board and prefabricated floor board will appear contraction and position change, leading to cracks at joints, which are generally vertical seams or horizontal seams. Cracking treatment method at the joints: It is recommended that the entire building be stabilized after the deformation has stabilized, and the repair within a short time is prone to repeated. Wall construction Bonded And Injection Molded Magnet Injection Molded Magnet,Bonded Neodymium Magnets,Injection Molded Neodymium Magnets,Injection Molded Bonded Magnet Honesun Industrial Co.,Limited , https://www.chinamagnetise.com
How to deal with cracking the wall? Different cracking causes have different treatment methods. The cracking of the wall caused by the above five causes has resulted in solutions for everyone. There is a crack in the walls of the house. Do not rush to fix it. Look for the cause of the cracking and do the treatment again. This will save you a lot of unnecessary work. I hope that today's content will be helpful to everyone. If you still want to learn more about this, follow our website.