FHM fence factory provides a variety of Garden Fencing Kits to support your selling.You could have a multiple choice here.FENCING ACCESSORIES ALL MADE FROM GALVANIZED COATED STEEL - easy replacement of parts for your Garden Fence needs.Such as Garden Fence Accessories,Garden Fence Fittings,Pvc Garden Fence Fittings,Garden Fence Kits DINGZHOU FEIHONG METAL MESH CO.,LTD , https://www.fhmfencing.com
1, the scale body material: all stainless steel body, after polishing, drawing processing, stainless steel skeleton, more durable. Highly waterproof and corrosion resistant.
2, the scale structure: the use of 25 stainless steel pressed U-type production, extremely strong.
3. The single-layer standard structure is accompanied by 4 sets of adjustable feet. On the general ground, the level of the scale can be flexibly adjusted, and the requirement for the ground is low.
4, four high-precision high-strength stainless steel cantilever beam sensor 5, HQ-4 hole dedicated waterproof junction box, the use of high-precision potentiometer and stainless steel shell, waterproof performance.
Second, the electronic platform operating method:
1. Keep good weighing habits when using. During the weighing process, try to place it in the middle of the electronic platform and let the four loadometers balance the force. Do not be convenient for drawing, often weighing in a corner, resulting in uneven sensor force, affecting the service life of the electronic loadometer.
2. When weighing, overload should be avoided to ensure that the platform scale is not damaged and the measurement is accurate. Clean the debris on the side of the sensor frequently to avoid contact with the load cell, resulting in inaccurate weighing and hops.
3. It is forbidden to perform arc welding on the weighing platform, if arc welding operation must be performed on the weighing platform. Please note: Disconnect the signal cable from the weighing display controller; the arc welding ground must be set near the welded part and firmly contacted on the scale body. Do not use the sensor as part of the arc welding circuit.
4. The same phase line connected to the electronic platform shall not receive inductive loads, such as doorbells.
5. When weighing, the scale body should be placed flat, at the same time, avoid contact, collision or vibration with other items to ensure the accuracy of measurement.
6. Keep the wiring firmly and always check whether the limit clearance is reasonable to ensure normal use.
Third, the use of electronic scales environment:
1. Pay attention to the humidity and dust in the operating environment. Electronic scales are not recommended for long periods of time in open air environments, especially not for rain; operating environments are kept dry; electronic scales are used to avoid access to heat sources.
2. Because many use occasions may be threatened by pests and rats, some areas of the signal cable of electronic platform scales are exposed on the outside. Therefore, pests and rats must be destroyed.
3. In regions where lightning strikes frequently, or in thunderstorm season, reliable lightning arresters or other reliable lightning protection measures must be installed. Sensors and meters are all electrostatic sensitive devices and they must be effectively protected against static electricity during use. 
Fourth, electronic platform repair methods:
1. When the weighing indicator controller is not used for a long time (such as more than one month), the power supply should be checked according to the environmental conditions to avoid the impact of dampness or other bad gas erosion on reliability.
2. Avoid contact with corrosive substances and prolong service life. Non-waterproof platform scales should avoid water ingress of sensors, junction boxes, etc., damage or affect the measurement.
3. Regularly clean the sensor screws with rust, and keep the sensors clean without interference, so as not to cause changes to the sensor resistance and affect the weighing.
4. Periodically check the position of the horn screw to see if the screw position is within normal use.
5, electronic scales weighing display should be quickly powered off in the event of failure, can not accurately determine the cause of the malfunction should be informed to the company's professional engineers to check and organize, users are not free to open the chassis, but also can not be free to replace the internal parts;
Post cap,post band,middle post end,Y arm and wire tension. According to the surface treatment we have hot dipped galvanized and pvc coated . The color have dark green ,black,red etc.
Electronic floor scale repair method
First, the electronic platform features: