In life, the kitchen is the space we use every day, and the kitchen faucet has a heavy responsibility. With the tap, we can cook a variety of delicious food. So, the kitchen faucet is the only appliance that solves our daily life. So, how to buy a kitchen faucet? What is the kitchen faucet installation ? Let's take a look with Xiaobian. Kitchen faucet installation A kitchen faucet with a single hole kitchen faucet Because kitchen mixers are used more frequently, they are required to be stable. In addition to being moved around, it is easy to loosen, so the locknut must be tightened. At present, there are some faucets on the market that use nuts to fasten the nuts. This kind of stability is very good. If you can solve the problems of removing water, it will be a popular trend in the future. Single cold on the stainless steel basin, as long as fixed and then connected to the two 4 teeth on the end of a hose connected to the angle valve on the head under the faucet on the hot and cold like just a lot of water. There are several types of taps: single cold, mixed hot and cold. The single cold is very simple, directly on the wall of the pipe head, if it is mixed hot and cold, it should be clear that the wall of hot and cold water pipes, usually left hot right cold. The faucet is still quite elaborate, for example, consider children cooking at home, and taps should be installed lower. In order to prevent the water from flowing down the sleeves of the clothes to wet the clothes. Kitchen faucet installation II. Installation of thermostatic faucet Before installing the thermostat, please check whether the water pipe is hot or cold. Remember not to connect the hot and cold water pipes incorrectly to prevent the faucet from working properly. Gas and solar water heaters cannot use thermostats because the water pressure is too low. Do not forget to install the hot and cold water filter when installing the thermostat. Kitchen Faucet Installation Three, Single Hole Kitchen Faucet Installation The requirement is stable, because the kitchen mixer is used frequently, and it is easy to loosen and move it. Therefore, the lock nut must be tightened. At present, there are some faucets on the market that use nuts to fasten the nuts. This kind of stability is very good. If you can solve the problems of removing water, it will be a popular trend in the future. Ready to install tools, check whether the complete set of accessories before installation, common faucet parts are: hose, rubber gasket, shower, go to water, kidnappers, decorative caps and so on. Kitchen faucet installation four, accessories preparation 1, a full set of fixed bolts and fixed copper sheets and gaskets; 2, a full set of basin to pull the water heater; 3, two inlet pipes. Then remove the faucet, pull the handle up and down, feel the open and close, and feel light and smooth, with a gentle and even sense of blockiness. The next step is to check that the plating surface is bright, free of bubbles, spots, and scratches. Kitchen faucet purchase knowledge 1, to use smoothly: vegetables, steamed rice, soup, brush bowl ... ... annoying thing in the kitchen too much, it is best not to let the leading to add chaos! With a smooth faucet, often people do not feel it Existence, and this is mainly related to its spool, handle position, switch mode. A good tap valve can be easily opened and closed, and the handle will not be too loose or too tight when used. The position and shape of the handle should be easy to open and close. Even with the back of the hand, it can be easily operated. Traditional spiral and wrench type switches are no longer needed in the kitchen. Instead, a quick lift switch closes. 2, easy to clean: the kitchen will use the hands with grease, dirt to open the faucet, the faucet dirty. Therefore, it is best to choose a product that does not stain oil and facilitate scrubbing. This has a lot to do with the shape and plating of the faucet. Generally, faucets with complex shapes and changing lines tend to leave clean corners. The surface of the thin, low-hardness faucet is prone to rust, and the cleaning is not clean. The fence recommends that people still use a product that is simple in shape and hard-coated, which can save a lot of things. 3, the size is right: Some families of kitchen faucets easy to splash water, falling water can not reach the center of the sink ... ... This is ignored the sink, kitchen faucet with the. When choosing a kitchen faucet, be sure to know the sink size and choose the right faucet for this size. Make sure that the angle of the water outlet is right in the center of the sink. There can be a 180° or 360° rotation, and the distance from the bottom of the sink is hardly splashed. 4. Water saving and environmental protection: The consumption of water resources in the kitchen is very large, and the modern decoration “energy saving and environmental protection†is the mainstream. Therefore, it is necessary to pay attention to this point when selecting the tap. Water-saving faucets will save 30-40% more water than regular faucets, which can save a lot of water bills for households. There are two main types of water-saving faucets. One is to use good bubblers to inject air into the water to prevent falling water from splashing and keep the flushing effect. At the same time, it slows the flow of water and reduces the flow of water to save water. The other is the handle "hint" design, when the handle is lifted to a certain height, there is a clear sense of stoppage, reminding the use of water has increased. 5, the style of unity: the unity of the decoration style is also more concerned about everyone, in the kitchen room, the sink can be used with different materials and styles, and the leader is mainly reflected in the online bar shape and surface coating. The above about the kitchen faucet installation and kitchen faucet purchase is briefly introduced here, and I hope to help you. For more information, please visit this website. Stay tuned. Faucet
Sheet & Pipe Plasma Cutting Machine mainly for 3 axis 2D drawing cutting and round pipe cutting
1.This design fit for multifunction cutting requirements: both metal sheet and pipe cutting
2. Accept OEM for any pipe cutting diameter and working length. ( Normally from 100mm up to 600mm dia. )
3. Accept OEM for any table size: likes 4x4, 4x8 Plasma Cutting Table
4. Accept any materials cutting: Iron plate, Stainless steel plate, Titanium plate, Galvanized sheet, Aluminum plate, High speed steel etc Steel Pipe Cutter,Sheet Cutting Machine,Metal Sheet Cutting Machine,Stainless Steel Cutting Machine Jinan Huaxia Machinery Equipment CO.,Ltd , https://www.cnmetalcutting.com
