Three trees paint plate coating cement paint
Hopper Feed Rivet T Nuts
Briefly introduction:
Embedded T Nuts are our company most competitive products.It use advanced production technique and completely realizes automation from stamping,forming to final tapping.The monthly production capacity is 55000.000.
Application:
1. T nuts takes a dowel screw and is used to fix wooden legs and castors to furniture. Available free of charge with sets of wooden furniture legs from Heritage Upholstery Supplies and an ideal solution for securely fitting legs and feet to your chairs, sofas, beds and other furniture. The standard fitting in the furniture industry.
2. The raw material is: carbon steel or stainless steel (304/316). 4 Prong T-Nuts can be used in hard
and soft woods .
Hebei Xinyu Metal Products Co.,Ltd is a ISO9001 cerificated enterprise,which specialize in Hopper Feed Rivet T Nuts Hopper Feed Rivet T Nuts,T Nut Fasteners,Special T Slot Nuts,Pronged Tee Nut Hebei Xinyu Metal Products Co.,Ltd , http://www.t-nuts.net
Check the surface of the base layer for dust, oil, impurities, whether the base layer is firm and firm, whether the base layer has cracks, whether it is smooth, vertical, and whether it is dry.
2 Primary treatment
Qualified is that the grass-roots level is the guarantee of aesthetics and durability of the paint. It is a common disease to cause cracking of the putty layer and the paint layer due to grass-roots factors (such as cement mortar or wall cracking). The treatment of the base layer cracks with a bandage is a common method for interior wall finishing. If the original cover white wall surface uses inferior glue, it shall be reinforced with alkali-resistant primer, and the wall surface shall be powdered and shall be removed.
3 wooden board closed
Avoid board surface deformation and color transmission.
4 patch bandage
To ensure the smoothness and firmness of the interface around the seam is the key point of the seam. Paste two layers of bandages to reduce cracks in the paint layer.
5 Partial batch scraping
The grass-roots flatness is not enough, and it is necessary to grind and level the uneven parts first; but when the deviation of the grass-roots flatness exceeds 8mm, it cannot be super-thickened and leveled with a putty, and the cement mortar is used for leveling.
6 Grinding
Polish the putty to ensure that the grass is roughly flat.
7 The first full scraper
The construction strives not to leave the end without scratching and leaving no seam marks.
8 The second full scraper
PuTTY is generally scraped twice to survive, and each time PuTTY is not to be spaced too long, the putty thickness is 1~3mm.
9 Yin Yang corner straight
Ensure that the yin and yang angles are linear.
10 The third pass is full of scraping
When there is a high requirement for the smoothness of the wall surface, putty scraping can be increased again, but the thickness of the last batch scraping scraper should not be less than 0.8 mm.
11 Grinding
The paint has a high requirement for the flatness of the putty layer, and it should be polished and flattened, and the putty layer should not be too hard so as to prevent the putty layer from being too smooth after sanding, without fine sand marks, which is not conducive to the bite of the coating on the putty layer.
12 first pass primer
The function of the primer is alkali-resistant closure. Reinforced putty, covered with fine sand marks, so the first time the paint layer should try to get through the putty layer.
13 Refilling putty
The putty layer appears broken during grinding. When the sand hole is used, putty should be repaired after the first pass.
14 Grinding
After refilling the putty, it should leave a mark and should be polished to avoid affecting the integrity of the paint.
15 Second pass primer
In order to ensure the finish coating effect, the total thickness of the primer should be 30mm, and it should not be used to save labor and save the material only once.
16 Grinding
The leveling of the primer is not enough and should be polished on the top coat to ensure the smooth finish of the top coat.
17 first pass coating
The first pass of spraying or roller coating should be uniform, and it can't be used for one-time spraying. The roller is too thick and affects the adhesive force.
18 Second pass coating
The second time spray. After the roller coating should pay attention to maintenance, should not be strong ventilation, so as not to produce shrinkage force in the coating layer of ventilation, resulting in coating cracking.
manufacturing and exporting Furniture Nuts .Product including
Wing Nuts , Hopper Feed T Nuts , Propeller Nuts , Weld Nuts , Pallet Nuts , Locking Nuts , Rivet Nuts , Doggie Tooth Washers , Steel Stamped Parts ,Hopper Feed Rivet T Nuts, Metal Stamped Parts ,
T-Nuts For Cliff-Climbing,Furniture Nuts, Tee Nut For Rock Climbing holding, Insert Tee Nut ,Middle steel Zinc Plated Stamping Wing Nut, Auto Flat Plane Weld Nuts ,
Automobile Spot Welding Nut,Customer-Made Metal Stamping Parts, Cold Heading Tee Nuts ,Stainless Steel Butterfly Nuts, Furniture Eccentric Wheel , Cam Lock Furniture Nut .
Our key strength are custom made special fasteners according to drawing or sample .We have longer and stable business relationship with well-known companies from American, Poland,Germany,French and so on.In the future ,xinyu will continue focusing on innovation special designed products,becoming your most trusted partner.
18-step construction process and acceptance criteria for interior wall paint
1 Grassroots inspection, cleaning